
Leaking Tap Repairs
We strip the tap, replace the worn washer, O-ring or jumper valve, and re-seat the spindle so the drip stops at the source instead of coming back again next month.
Plumbing Spring Hill re-seats, rebuilds and replaces taps across the suburb, from pre-1940 cottage brass to modern mixers, with a fixed quote before any work starts and same-day where we can.
If we're late, $100 comes off your bill

A dripping tap on the Spring Hill side of the ridge rarely needs a whole new fixture, but it does need somebody who knows the difference. That is the job we do.

Most taps here have outlived several sets of owners. The fix is in the detail: matching the part to the spindle, not just swapping whatever washer is in the kit.

The pre-1940 housing era left this ridge with tap bodies whose spindles and seats predate today's standard washer sizes. A washer that suits a new tap will not seal a century-old one, so we re-seat and match parts instead of guessing.
Some of the oldest dwellings still hold galvanised service pipes from early re-plumbing, which rust at the unions and choke flow. A weak tap is sometimes a line problem wearing a tap's clothes.
At the last census most homes here were rented, so the landlord or property manager approves the job, and we paper the quote for them before any fitting is touched.
From one washer in a Gregory Terrace flat to a full fixture swap in a converted cottage nearby, here is the tap work our plumbers do across this steep ridge:

We strip the tap, replace the worn washer, O-ring or jumper valve, and re-seat the spindle so the drip stops at the source instead of coming back again next month.

A stiff mixer gets its cartridge swapped, the body cleaned and the spout seals renewed, so the handle turns freely again and the tap shuts off cleanly every time.

A groove worn in the tap seat chews new washers quickly, so we machine the seat flat, fit a fresh washer and stop the same tap failing three times running.

Garden taps cop sun and storm year after year, so we replace perished washers and split hoses, secure loose mountings and check the stand for movement that opens joints underground.

When a tap screams or spits, the fault is usually in the line, so we trace pressure and flow back to the fixture and fix the cause, not the symptom.

Where a tap body is past saving, we supply and fit a matching replacement, remove the old fixture and leave the basin, wall or laundry point ready for daily use.
$0 call-out fees, available 24/7, and same-day where we can.

Four calls make up most of our tap work here. Each one has a cause we can name and a fix we can price before we start.
The drip comes back because the seat is grooved or the spindle is worn, not because the washer was wrong, and one proper re-seating job ends the cycle for good.
Handles seize when old tap bodies corrode inside, and a full strip and grease returns smooth movement, so nobody has to force a stiff tap shut with pliers ever again.
The scream is air or restriction in the line, usually at a kinked flexi or a partly closed stop tap, and clearing or replacing that small section silences the fixture.
Pipes bang when a fast-closing mixer sends a shock wave down loose runs, and securing the line or fitting a small arrestor protects the joints and fittings behind your walls.

A tap that never quite closes is never just a nuisance, especially on a ridge where the housing is this old and mostly rented, and here is what it turns into when it waits:
A drip works the meter day and night, and nobody stands over the vanity at 2am to watch it. The repair costs less than the months of water it wastes.
Water tracks along a tap stand or a basin trap into timber and plaster, and a heritage cottage holds plenty of both. The stain on the vanity is usually the first sign.
A scream or a hammering line points at pressure or loose runs, and on streets that fall away from the crest, the lower houses push more through tired fittings than the ridge-top ones. Fixing the symptom leaves the cause waiting.

Phone (07) 3067 4289 with what's happening in Spring Hill. A few questions on the call mean the right parts come with us.

Flat-rate pricing and no hidden fees, set before the job starts. Give the go-ahead and we begin.

With the water off at the meter, our Spring Hill plumber strips the tap, names the worn part, re-seats or replaces what the quote covers and tests the fixture under full pressure.

Settle by card or EFTPOS when the work is done, or ask us about Fix now, pay later.

Every tap on this ridge gets that same treatment, whether it is a laundry tap in a 1960s flat or the original brass in a worker's cottage.
You pay zero call-out fees in Spring Hill, and there's no extra charge for nights, weekends or public holidays.

Our Fix-It-or-It's-Free guarantee covers the job (T&Cs apply), and if we're late, $100 comes off your bill.
Every job is handled by a licensed plumber under QBCC No: 15024607, and the labour has a lifetime labour warranty.
Locally owned and operated, licensed and insured, with flat-rate pricing on every job.
We also work Herston, Bowen Hills, Fortitude Valley, Brisbane City and Petrie Terrace, plus the lanes between them, so a dripping mixer one suburb over sits on the same run as a cottage tap up the hill.
Worn seats and aged spindles are usually the cause, because a washer alone cannot seal a grooved seat, so we re-seat the tap and fit parts matched to the original spindle.
In most cases yes, we source washers and jumpers to suit aged spindles, machine worn seats flat and keep the original handles, so the cottage keeps its old brass tapware.
It does, because a tap that never fully closes runs water down the drain all day, stains vanities and feeds mould in a sealed unit bathroom, so it is worth fixing early.
Tenants ring us and we are happy to talk the job through, but approval for the price must come from the landlord or managing agent, and we email the paperwork through before the first visit.
No, the utility's responsibility ends at the street main, while every fitting past your boundary belongs to you or your landlord, so this repair is one you book yourself.
Ring (07) 3067 4289, tell us which taps are dripping or stiff and where you sit on the ridge, and we book you in with the fixed quote before work starts.
Ring (07) 3067 4289 and tell us what's happening. We're available 24/7, jobs in Spring Hill come with zero call-out fees and flat-rate pricing, and every job is done under QBCC No: 15024607, same-day when we can.
For the wider range of general plumbing work, including toilet repairs and kitchen plumbing, start at the general plumbing page.
To claim your $0 call-out fee, call (07) 3067 4289 today.